Bush-hog RMB 1660 Bedienungsanleitung

©2010 Alamo Group Inc.$0.00Published 10/10 Part No. 50068816COPERATOR’S MANUAL BUSH HOG® 2501 Griffin Ave. Selma, AL 36703334-874-2700www.bushhog.c

SAFETYRMB 1660 11/10 Safety Section 1-4© 2010 Alamo Group Inc.SAFETYKEEP AWAY FROM ROTATING ELEMENTS to prevent entanglementand possible serious inj

MAINTENANCERMB 1660 11/10 Maintenance Section 5-2© 2010 Alamo Group Inc.MAINTENANCELUBRICATIONGeneralGrease all locations shown daily.PTO SHAFT INSP

MAINTENANCERMB 1660 11/10 Maintenance Section 5-3© 2010 Alamo Group Inc.MAINTENANCEHYDRAULIC SYSTEMOil SupplyCheck daily the oil level in the reserv

MAINTENANCERMB 1660 11/10 Maintenance Section 5-4© 2010 Alamo Group Inc.MAINTENANCEHose Replacement1. Replace one hose at a time to avoid the risk o

MAINTENANCERMB 1660 11/10 Maintenance Section 5-5© 2010 Alamo Group Inc.MAINTENANCEFLAILHEAD1. Frequently inspect the rotor assembly for damaged or

MAINTENANCERMB 1660 11/10 Maintenance Section 5-6© 2010 Alamo Group Inc.MAINTENANCEPTO GEARBOXRefill the gearbox after the first initial 50 hours an

MAINTENANCERMB 1660 11/10 Maintenance Section 5-7© 2010 Alamo Group Inc.MAINTENANCEPROPER TORQUE VALUES FOR FASTENERSThe chart lists the correct tig

LIMITED WARRANTYBush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized

TO THE OWNER/OPERATOR/DEALERTo keep your implement running efficiently and safely, read your manual thoroughly and follow these directionsand the Saf

RMB 1660-11/10 P/N 50068816CPrinted U.S.ARMB 1660REAR MOUNT BOOM MOWER

SAFETYRMB 1660 11/10 Safety Section 1-5© 2010 Alamo Group Inc.SAFETYConnecting & Disconnecting Implement Safety Instructions & PracticesThe

SAFETYRMB 1660 11/10 Safety Section 1-6© 2010 Alamo Group Inc.SAFETYEquipment Operation Safety Instructions and PracticesNever leave the Tractor and

SAFETYRMB 1660 11/10 Safety Section 1-7© 2010 Alamo Group Inc.SAFETYFollow these guidelines to reduce the risk of equipment andgrass fires while ope

SAFETYRMB 1660 11/10 Safety Section 1-8© 2010 Alamo Group Inc.SAFETYFlail Mowers are capable under adverse conditions of throwingobjects for great d

SAFETYRMB 1660 11/10 Safety Section 1-9© 2010 Alamo Group Inc.SAFETYDo not mount or dismount the Tractor while the tractor is moving. Mountthe Tract

SAFETYRMB 1660 11/10 Safety Section 1-10© 2010 Alamo Group Inc.SAFETYDo Not operate this equipment in areas where insects such as bees may attack yo

SAFETYRMB 1660 11/10 Safety Section 1-11© 2010 Alamo Group Inc.SAFETYMow at the speed that you can safely operate and control the tractor and mower.

SAFETYRMB 1660 11/10 Safety Section 1-12© 2010 Alamo Group Inc.SAFETYMaintenance and Service Safety Instructions and PracticesDo not let the Blades

SAFETYRMB 1660 11/10 Safety Section 1-13© 2010 Alamo Group Inc.SAFETYAlways maintain the safety signs in good readable condition. If the safety sign

To the Owner/Operator/DealerAll implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-mindedoperator who

SAFETYRMB 1660 11/10 Safety Section 1-14© 2010 Alamo Group Inc.SAFETYTransporting Safety Instructions and PracticesReplace bent or broken blades wit

SAFETYRMB 1660 11/10 Safety Section 1-15© 2010 Alamo Group Inc.SAFETYSecure the boom and mower head in the transport position before traveling on pu

SAFETYRMB 1660 11/10 Safety Section 1-16© 2010 Alamo Group Inc.SAFETYConcluding Safety Instructions and PracticesTransport only at speeds where you

SAFETYRMB 1660 11/10 Safety Section 1-17© 2010 Alamo Group Inc.SAFETYDecal LocationNOTE: Bush Hog supplies safety decals on this product to promote

SAFETYRMB 1660 11/10 Safety Section 1-18© 2010 Alamo Group Inc.SAFETYITEM PART NO. QTY LEVEL DESCRIPTION1. D433 1 Decal Sheet Multiple Hazard 2. D38

SAFETYRMB 1660 11/10 Safety Section 1-19© 2010 Alamo Group Inc.SAFETYITEM PART NO. QTY LEVEL DESCRIPTION1. 50061049 1 LOGO Bush Hog Logo (22”)2. 240

SAFETYRMB 1660 11/10 Safety Section 1-20© 2010 Alamo Group Inc.SAFETYDecal DescriptionMulti Hazard Decal Sheet P/N D433Decal D433 consists of the fo

SAFETYRMB 1660 11/10 Safety Section 1-21© 2010 Alamo Group Inc.SAFETYDriveline HazardsP/N D388Decal D388 consists of the following multi-hazards.

SAFETYRMB 1660 11/10 Safety Section 1-22© 2010 Alamo Group Inc.SAFETYIMPORTANT! Keep Sway Bar Chains TightP/N D355WARNING! Pinch PointsP/N 02962764D

SAFETYRMB 1660 11/10 Safety Section 1-23© 2010 Alamo Group Inc.SAFETYDANGER! Crushing HazardSerious injury can result from contact with movingboom.

In order to reduce accidents and enhance the safe operation of mowers, Bush Hog Division, in cooperation withother industry manufacturers has develope

SAFETYRMB 1660 11/10 Safety Section 1-24© 2010 Alamo Group Inc.SAFETYINFORMATION - Safety BookletD524Read Operator’s Manual! The operator’s manual i

SAFETYRMB 1660 11/10 Safety Section 1-25© 2010 Alamo Group Inc.SAFETYTO AVOID SERIOUS INJURY OR DEATH onlyoperate on Tractor equipped with fully enc

SAFETYRMB 1660 11/10 Safety Section 1-26© 2010 Alamo Group Inc.SAFETYEuro Multi Decal P/N 09.821.35Red Reflector. Keep reflectors clean and visible

SAFETYRMB 1660 11/10 Safety Section 1-27© 2010 Alamo Group Inc.SAFETYFederal Laws and RegulationsThis section is intended to explain in broad terms

Introduction Section 2-1© 2010 Alamo Group Inc.INTRODUCTION SECTION

INTRODUCTIONRMB 1660 11/10 Introduction Section 2-2© 2010 Alamo Group Inc.INTRODUCTIONThis Hydraulic Boom Mower is designed with care and built with

INTRODUCTIONRMB 1660 11/10 Introduction Section 2-3© 2010 Alamo Group Inc.INTRODUCTIONThe Bush Hog Boom Mower is primarily designed for grass cuttin

INTRODUCTIONRMB 1660 11/10 Introduction Section 2-4© 2010 Alamo Group Inc.INTRODUCTIONATTENTION OWNER/ OPERATORBEFORE OPERATING THIS MACHINE:1. Care

Assembly Section 3-1© 2010 Alamo Group Inc.ASSEMBLY SECTION

Alamo Group Ag. Division is willing to provideone (1) AEM Mower Safety Practices VideoPlease Send Me: VHS Format – AEM/FEMA Mower Operator Safety Vide

ASSEMBLYRMB 1660 11/10 Assembly Section 3-2© 2010 Alamo Group Inc.ASSEMBLYTRACTOR SELECTIONMINIMUM TRACTOR WEIGHTS - including ballast weight if nec

ASSEMBLYRMB 1660 11/10 Assembly Section 3-3© 2010 Alamo Group Inc.ASSEMBLYTRACTOR PREPARATIONFitting Operator GuardUse tractor with safety glass win

ASSEMBLYRMB 1660 11/10 Assembly Section 3-4© 2010 Alamo Group Inc.ASSEMBLYSuggestions to increase stability: • Increasing rear wheel track; a tracto

ASSEMBLYRMB 1660 11/10 Assembly Section 3-5© 2010 Alamo Group Inc.ASSEMBLYATTACHMENT TO TRACTOR• Reverse tractor squarely up to the machine.• Connec

ASSEMBLYRMB 1660 11/10 Assembly Section 3-6© 2010 Alamo Group Inc.ASSEMBLY• Fit the machine to top link• Raise machine on tractor linkage until the

ASSEMBLYRMB 1660 11/10 Assembly Section 3-7© 2010 Alamo Group Inc.ASSEMBLY• Replace the stabilizer quadrant pin and secure withthe clip pin.NOTE: T

ASSEMBLYRMB 1660 11/10 Assembly Section 3-8© 2010 Alamo Group Inc.ASSEMBLYCheck that the welded in pins between the stabilizers jaws are in contact

ASSEMBLYRMB 1660 11/10 Assembly Section 3-9© 2010 Alamo Group Inc.ASSEMBLY• Adjust using the mounting hole that allows theP.T.O. and gearbox shaft t

ASSEMBLYRMB 1660 11/10 Assembly Section 3-10© 2010 Alamo Group Inc.ASSEMBLY• Raise the stand legs into the work position andsecure with lock pins.•

ASSEMBLYRMB 1660 11/10 Assembly Section 3-11© 2010 Alamo Group Inc.ASSEMBLY• Fit PTO shaft in position. • Attach safety chains (A) on driveline to a

TABLE OF CONTENTSSAFETY SECTION ...1-1Gener

ASSEMBLYRMB 1660 11/10 Assembly Section 3-12© 2010 Alamo Group Inc.ASSEMBLYFlail Head AttachmentOperate machine controls to maneuver boom arminto fl

ASSEMBLYRMB 1660 11/10 Assembly Section 3-13© 2010 Alamo Group Inc.ASSEMBLYOIL REQUIREMENTSTankFill reservoir to approximately 2” below the top of t

ASSEMBLYRMB 1660 11/10 Assembly Section 3-14© 2010 Alamo Group Inc.ASSEMBLYRUNNING UP PROCEDURE1. Ensure that the rotor control valve is in "ST

ASSEMBLYRMB 1660 11/10 Assembly Section 3-15© 2010 Alamo Group Inc.ASSEMBLYSTORAGE If machine is to be left standing for an extended period of time,

Operation Section 4-1© 2010 Alamo Group Inc.OPERATION SECTION

OPERATIONRMB 1660 11/10 Operation Section 4-2© 2010 Alamo Group Inc.OPERATIONBUSH HOG RMB 1660 OPERATING INSTRUCTIONSBush Hog Boom Mowers are manufa

OPERATIONRMB 1660 11/10 Operation Section 4-3© 2010 Alamo Group Inc.OPERATION1. Standard Equipment and SpecificationsTractor Requirements:Minimum Tr

OPERATIONRMB 1660 11/10 Operation Section 4-4© 2010 Alamo Group Inc.OPERATION2. OPERATOR REQUIREMENTSSafe operation of the unit is the responsibilit

OPERATIONRMB 1660 11/10 Operation Section 4-5© 2010 Alamo Group Inc.OPERATION3. TRACTOR REQUIREMENTSIn addition to tractor horsepower and size requi

STARTING THE TRACTOR ... 4-1

OPERATIONRMB 1660 11/10 Operation Section 4-6© 2010 Alamo Group Inc.OPERATION3.3 Tractor Lighting and SMV EmblemIf the tractor will be operated near

OPERATIONRMB 1660 11/10 Operation Section 4-7© 2010 Alamo Group Inc.OPERATION3.6 Tractor HorsepowerThe horsepower required to operate the mower depe

OPERATIONRMB 1660 11/10 Operation Section 4-8© 2010 Alamo Group Inc.OPERATION3.9 Front End WeightA minimum of 20% total tractor weight must be maint

OPERATIONRMB 1660 11/10 Operation Section 4-9© 2010 Alamo Group Inc.OPERATION4.1 Boarding the TractorUse both hands and equipped handrails and steps

OPERATIONRMB 1660 11/10 Operation Section 4-10© 2010 Alamo Group Inc.OPERATION5. STARTING THE TRACTORThe operator must have a complete understanding

OPERATIONRMB 1660 11/10 Operation Section 4-11© 2010 Alamo Group Inc.OPERATION6. PRE-OPERATION INSPECTION AND SERVICEBefore each use, a pre-operatio

OPERATIONRMB 1660 11/10 Operation Section 4-12© 2010 Alamo Group Inc.OPERATION6.2 Boom Unit Pre-Operation Inspection and ServiceInspect and service

OPERATIONRMB 1660 11/10 Operation Section 4-13© 2010 Alamo Group Inc.OPERATIONFRAME ASSEMBLY• Ensure all bolts and screws are in position andare pro

OPERATIONRMB 1660 11/10 Operation Section 4-14© 2010 Alamo Group Inc.OPERATIONRelieve hydraulic pressure prior to doing any maintenance or repair wo

OPERATIONRMB 1660 11/10 Operation Section 4-15© 2010 Alamo Group Inc.OPERATIONAttention: Oil Filler Cap is also the Pressure Relief Cap.Remove cap s

Safety Section 1-1© 2010 Alamo Group Inc.SAFETY SECTION

OPERATIONRMB 1660 11/10 Operation Section 4-16© 2010 Alamo Group Inc.OPERATIONSICKLE BAR INSPECTION• Inspect blades and blade bolts for loosenessand

OPERATIONRMB 1660 11/10 Operation Section 4-17© 2010 Alamo Group Inc.OPERATIONBoom Mower PRE-OPERATION InspectionMower ID#:_________________________

OPERATIONRMB 1660 11/10 Operation Section 4-18© 2010 Alamo Group Inc.OPERATIONTractor PRE-OPERATION InspectionTractor ID#:________________________Ma

OPERATIONRMB 1660 11/10 Operation Section 4-19© 2010 Alamo Group Inc.OPERATION7. MACHINE CONTROLS7.1 Cable Controls - Identification & Function

OPERATIONRMB 1660 11/10 Operation Section 4-20© 2010 Alamo Group Inc.OPERATION7.2 Lever Functions

OPERATIONRMB 1660 11/10 Operation Section 4-21© 2010 Alamo Group Inc.OPERATION7.3 Rotor Control

OPERATIONRMB 1660 11/10 Operation Section 4-22© 2010 Alamo Group Inc.OPERATION8. BREAKAWAYThe machine is fitted with a hydraulic breakaway device wh

OPERATIONRMB 1660 11/10 Operation Section 4-23© 2010 Alamo Group Inc.OPERATION9. ROTOR OPERATING SPEEDEnsure that the rotor control lever is in the

OPERATIONRMB 1660 11/10 Operation Section 4-24© 2010 Alamo Group Inc.OPERATION12. Hedge Cutting ProcedureCut the side and bottom of the field side f

OPERATIONRMB 1660 11/10 Operation Section 4-25© 2010 Alamo Group Inc.OPERATION12.1 Working on Adverse SlopesWhen working high with the reach fully e

SAFETYRMB 1660 11/10 Safety Section 1-2© 2010 Alamo Group Inc.SAFETYGeneral Safety Instructions and PracticesA careful operator is the best operator

OPERATIONRMB 1660 11/10 Operation Section 4-26© 2010 Alamo Group Inc.OPERATION14. DRIVING THE TRACTOR AND IMPLEMENTSafe tractor transport requires t

OPERATIONRMB 1660 11/10 Operation Section 4-27© 2010 Alamo Group Inc.OPERATION14.1 Starting the TractorThe procedure to start the tractor is model s

OPERATIONRMB 1660 11/10 Operation Section 4-28© 2010 Alamo Group Inc.OPERATION14.3 Driving the Tractor and BoomStart off driving at a slow speed and

OPERATIONRMB 1660 11/10 Operation Section 4-29© 2010 Alamo Group Inc.OPERATION15.1 Foreign Debris HazardsBefore mowing, inspect the area to make sur

OPERATIONRMB 1660 11/10 Operation Section 4-30© 2010 Alamo Group Inc.OPERATIONFlail Mowers are capable under adverse conditions of throwingobjects f

OPERATIONRMB 1660 11/10 Operation Section 4-31© 2010 Alamo Group Inc.OPERATION15.4 Operating Speed and Ground SpeedGround speed for mowing will depe

OPERATIONRMB 1660 11/10 Operation Section 4-32© 2010 Alamo Group Inc.OPERATIONThere are obvious and hidden potential hazards in the operation of thi

OPERATIONRMB 1660 11/10 Operation Section 4-33© 2010 Alamo Group Inc.OPERATION15.6 Operating the Attached Mower HeadsRefer to the Assembly Section o

OPERATIONRMB 1660 11/10 Operation Section 4-34© 2010 Alamo Group Inc.OPERATION15.7 Shutting Down the Attached HeadTo shut down attached mower head,

OPERATIONRMB 1660 11/10 Operation Section 4-35© 2010 Alamo Group Inc.OPERATION16. TRACTOR, BOOM, AND ATTACHED HEAD STORAGEProperly preparing and sto

SAFETYRMB 1660 11/10 Safety Section 1-3© 2010 Alamo Group Inc.SAFETYOperator Safety Instructions and PracticesEngine Exhaust, some of its constituen

OPERATIONRMB 1660 11/10 Operation Section 4-36© 2010 Alamo Group Inc.OPERATION17.1 Transport Position• Select ROTOR OFF and wait until rotor hasstop

OPERATIONRMB 1660 11/10 Operation Section 4-37© 2010 Alamo Group Inc.OPERATION18. TRANSPORT POSITION-Head AttachedThe machine is transported in line

OPERATIONRMB 1660 11/10 Operation Section 4-38© 2010 Alamo Group Inc.OPERATION19.1 Transport HeightThere is no fixed dimension for transport height.

OPERATIONRMB 1660 11/10 Operation Section 4-39© 2010 Alamo Group Inc.OPERATIONNever allow children or other persons to ride on the Tractor or Implem

OPERATIONRMB 1660 11/10 Operation Section 4-40© 2010 Alamo Group Inc.OPERATIONWhen operating on public roads, haveconsideration for other road users

OPERATIONRMB 1660 11/10 Operation Section 4-41© 2010 Alamo Group Inc.OPERATION19.3 Hauling the Tractor and ImplementBefore transporting a loaded tra

OPERATIONRMB 1660 11/10 Operation Section 4-42© 2010 Alamo Group Inc.OPERATION20. TROUBLESHOOTING GUIDETROUBLE POSSIBLE CAUSE POSSIBLE REMEDYHydraul

OPERATIONRMB 1660 11/10 Operation Section 4-43© 2010 Alamo Group Inc.OPERATIONTROUBLE POSSIBLE CAUSE POSSIBLE REMEDYExcessive Vibrations Blade Broke

Maintenance Section 5-1© 2010 Alamo Group Inc.MAINTENANCE SECTION